Texas Instruments BQ24158 Даташит, BQ24158 PDF, даташитов
| Другие PDF | недоступен. | |
| BQ24158 Datasheet PDF : | ||
Description
The bq24153A/6A/8/9 is a compact, flexible, high efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.
Features
• Charge Faster than Linear Chargers
• High-Accuracy Voltage and Current Regulation
– Input Current Regulation Accuracy: ±5% (100 mA and 500 mA)
(25°C), ±1% (0°C to 125°C)
– Charge Current Regulation Accuracy: ±5%
• Input Voltage Based Dynamic Power
Management (VIN DPM)
• Bad Adaptor Detection and Rejection
• Safety Limit Register for Maximum Charge
Voltage and Current Limiting
• High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
• 20-V Absolute Maximum Input Voltage Rating
• 9-V Maximum Operating Input Voltage
bq24156A/9
• 6-V Maximum Operating Input Voltage
bq24153A/8
• Built-In Input Current Sensing and Limiting
• Integrated Power FETs for Up To 1.55-A Charge Rate
• Programmable Charge Parameters through I2C™
Compatible Interface (up to 3.4 Mbps):
– Input Current Limit
– VIN DPM Threshold
– Fast-Charge/Termination Current
– Charge Regulation Voltage (3.5 V to 4.44 V)
– Low Charge Current Mode Enable/Disable
– Safety Timer with Reset Control
– Termination Enable/Disable
• Support up to 1.55 A Charge Current Using 55-mΩ Sensing Resistor
• Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
• Automatic High Impedance Mode for Low Power
Consumption
• Robust Protection
– Reverse Leakage Protection Prevents Battery
Drainage
– Thermal Regulation and Protection
– Input/Output Overvoltage Protection
• Status Output for Charging and Faults
• USB Friendly Boot-Up Sequence
• Automatic Charging
• Power Up System without Battery bq24158/9
• Boost Mode Operation for USB OTG:
(bq24153A/8 only)
– Input Voltage Range (from Battery): 2.5 V to
4.5 V
– Output for VBUS: 5.05 V/ 200 mA
• 2.1 mm x 2 mm 20-Pin WCSP Package
Applications
• Mobile and Smart Phones
• MP3 Players
• Handheld Devices
| Page Links : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 |
| Номер в каталоге | Описание (Функция) | производитель | |
| FAN54013BUCX | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| FAN5400 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB137C | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB OTG/HDMI/MHL Support | Summit Microelectronics | |
| FAN54040 | USB-OTG, 1.55 A, Li-Ion Switching Charger with Power Path and 2.3 A Production Test Support | Fairchild Semiconductor | |
| SMB136 | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| SMB137B | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| FAN54010 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB138 | Summit Microelectronics | ||
| RT9503 | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology | |
| RT9503A | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology |
English 한국어 简体中文 日本語 español
ru.datasheetbank.com
Texas Instruments BQ24158 Даташит, BQ24158 PDF, даташитов
| Другие PDF | недоступен. | |
| BQ24158 Datasheet PDF : | ||
Description
The bq24153A/6A/8/9 is a compact, flexible, high efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.
Features
• Charge Faster than Linear Chargers
• High-Accuracy Voltage and Current Regulation
– Input Current Regulation Accuracy: ±5% (100 mA and 500 mA)
– Charge Voltage Regulation Accuracy: ±0.5%
(25°C), ±1% (0°C to 125°C)
– Charge Current Regulation Accuracy: ±5%
• Input Voltage Based Dynamic Power
Management (VIN DPM)
• Bad Adaptor Detection and Rejection
• Safety Limit Register for Maximum Charge
Voltage and Current Limiting
• High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
• 20-V Absolute Maximum Input Voltage Rating
• 9-V Maximum Operating Input Voltage
bq24156A/9
• 6-V Maximum Operating Input Voltage
bq24153A/8
• Built-In Input Current Sensing and Limiting
• Integrated Power FETs for Up To 1.55-A Charge Rate
• Programmable Charge Parameters through I2C™
Compatible Interface (up to 3.4 Mbps):
– VIN DPM Threshold
– Fast-Charge/Termination Current
– Charge Regulation Voltage (3.5 V to 4.44 V)
– Low Charge Current Mode Enable/Disable
– Safety Timer with Reset Control
– Termination Enable/Disable
• Support up to 1.55 A Charge Current Using 55-mΩ Sensing Resistor
• Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
• Automatic High Impedance Mode for Low Power
Consumption
• Robust Protection
– Reverse Leakage Protection Prevents Battery
Drainage
– Thermal Regulation and Protection
– Input/Output Overvoltage Protection
• Status Output for Charging and Faults
• USB Friendly Boot-Up Sequence
• Automatic Charging
• Power Up System without Battery bq24158/9
• Boost Mode Operation for USB OTG:
(bq24153A/8 only)
– Input Voltage Range (from Battery): 2.5 V to
– Output for VBUS: 5.05 V/ 200 mA
• 2.1 mm x 2 mm 20-Pin WCSP Package
Applications
• Mobile and Smart Phones
• MP3 Players
• Handheld Devices
| Ссылка на страницу (HTML): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 |
| Номер в каталоге | Описание (Функция) | производитель | |
| FAN54013BUCX | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| FAN5400 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB137C | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB OTG/HDMI/MHL Support | Summit Microelectronics | |
| FAN54040 | USB-OTG, 1.55 A, Li-Ion Switching Charger with Power Path and 2.3 A Production Test Support | Fairchild Semiconductor | |
| SMB136 | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| SMB137B | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| FAN54010 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB138 | Programmable Switch-mode, USB/AC Input Li+ Battery Charger with TurboCharge™ Mode and USB “On- the-Go” Power | Summit Microelectronics | |
| RT9503 | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology | |
| RT9503A | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology |
English 한국어 简体中文 日本語 español
ru.datasheetbank.com
Texas Instruments BQ24158YFFR Даташит, BQ24158YFFR PDF, даташитов
| Другие PDF | недоступен. | |
| BQ24158YFFR Datasheet PDF : | ||
Description
The bq24153A/6A/8/9 is a compact, flexible, high efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.
Features
• Charge Faster than Linear Chargers
• High-Accuracy Voltage and Current Regulation
– Input Current Regulation Accuracy: ±5% (100 mA and 500 mA)
– Charge Voltage Regulation Accuracy: ±0.5%
(25°C), ±1% (0°C to 125°C)
– Charge Current Regulation Accuracy: ±5%
• Input Voltage Based Dynamic Power
Management (VIN DPM)
• Bad Adaptor Detection and Rejection
• Safety Limit Register for Maximum Charge
Voltage and Current Limiting
• High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
• 20-V Absolute Maximum Input Voltage Rating
• 9-V Maximum Operating Input Voltage
bq24156A/9
• 6-V Maximum Operating Input Voltage
bq24153A/8
• Built-In Input Current Sensing and Limiting
• Integrated Power FETs for Up To 1.55-A Charge Rate
• Programmable Charge Parameters through I2C™
Compatible Interface (up to 3.4 Mbps):
– Input Current Limit
– VIN DPM Threshold
– Fast-Charge/Termination Current
– Charge Regulation Voltage (3.5 V to 4.44 V)
– Low Charge Current Mode Enable/Disable
– Safety Timer with Reset Control
– Termination Enable/Disable
• Support up to 1.55 A Charge Current Using 55-mΩ Sensing Resistor
• Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
• Automatic High Impedance Mode for Low Power
Consumption
• Robust Protection
– Reverse Leakage Protection Prevents Battery
Drainage
– Thermal Regulation and Protection
– Input/Output Overvoltage Protection
• Status Output for Charging and Faults
• USB Friendly Boot-Up Sequence
• Automatic Charging
• Power Up System without Battery bq24158/9
• Boost Mode Operation for USB OTG:
(bq24153A/8 only)
– Input Voltage Range (from Battery): 2.5 V to
4.5 V
– Output for VBUS: 5.05 V/ 200 mA
• 2.1 mm x 2 mm 20-Pin WCSP Package
Applications
• Mobile and Smart Phones
• MP3 Players
• Handheld Devices
| Page Links : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 |
| Номер в каталоге | Описание (Функция) | производитель | |
| FAN54013BUCX | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| FAN5400 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB137C | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB OTG/HDMI/MHL Support | Summit Microelectronics | |
| FAN54040 | USB-OTG, 1.55 A, Li-Ion Switching Charger with Power Path and 2.3 A Production Test Support | Fairchild Semiconductor | |
| SMB136 | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| SMB137B | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| FAN54010 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB138 | Programmable Switch-mode, USB/AC Input Li+ Battery Charger with TurboCharge™ Mode and USB “On- the-Go” Power | Summit Microelectronics | |
| RT9503 | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology | |
| RT9503A | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology |
English 한국어 简体中文 日本語 español
ru.datasheetbank.com
Texas Instruments BQ24158YFFR_10 Даташит, BQ24158YFFR_10 PDF, даташитов
| Другие PDF | недоступен. | |
| BQ24158YFFR_10 Datasheet PDF : | ||
DESCRIPTION
The bq24153/6/8 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I2C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.
FEATURES
• Charge Faster than Linear Chargers
• High-Accuracy Voltage and Current Regulation
– Input Current Regulation Accuracy: ±5%
(100 mA and 500 mA)
– Charge Voltage Regulation Accuracy:
±0.5% (25°C), ±1% (0°C to 125°C)
– Charge Current Regulation Accuracy: ±5%
• Input Voltage Based Dynamic Power
Management (VIN DPM)
• Bad adaptor detection and rejection
• Safety limit register for maximum charge
voltage and current limiting
• High-Efficiency Mini-USB/AC Battery Charger
for Single-Cell Li-Ion and Li-Polymer Battery
Packs
• 20-V Absolute Maximum Input Voltage Rating
• 9.0-V Maximum Operating Input
Voltage-bq24156
• 6-V Maximum Operating Input
Voltage-bq24153/8
• Built-In Input Current Sensing and Limiting
• Integrated Power FETs for Up To 1.5-A Charge
Rate-bq24156, 1.25A-bq24153/8
• Programmable Charge Parameters through
I2C™ Compatible Interface (up to 3.4 Mbps):
– Input Current Limit
– VIN DPM Threshold
– Fast-Charge/Termination Current
– Charge Regulation Voltage (3.5 V to 4.44 V)
– Low Charge Current Mode Enable/Disable
– Safety Timer with Reset Control
– Termination Enable/Disable
• Synchronous Fixed-Frequency PWM
Controller Operating at 3 MHz With 0% to
99.5% Duty Cycle
• Automatic High Impedance Mode for Low
Power Consumption
• Robust Protection
– Reverse Leakage Protection Prevents
Battery Drainage
– Thermal Regulation and Protection
– Input/Output Overvoltage Protection
• Status Output for Charging and Faults
• USB Friendly Boot-Up Sequence
• Automatic Charging
• Power Up System without Battery bq24158
• Boost Mode Operation for USB OTG:
(bq24153/8 only)
– Input Voltage Range (from Battery): 2.5 V to 4.5 V
– Output for VBUS: 5.05 V/ 200 mA
• 2.1 mm x 2 mm 20-Pin WCSP Package
APPLICATIONS
• Mobile and Smart Phones
• MP3 Players
• Handheld Devices
| Page Links : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 |
| Номер в каталоге | Описание (Функция) | производитель | |
| FAN54013BUCX | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| FAN5400 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB137C | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB OTG/HDMI/MHL Support | Summit Microelectronics | |
| FAN54040 | USB-OTG, 1.55 A, Li-Ion Switching Charger with Power Path and 2.3 A Production Test Support | Fairchild Semiconductor | |
| SMB136 | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| SMB137B | Programmable Switching Li+ Battery Charger with USB/AC Input, CurrentPath™ Manager, TurboChargeTM Mode*, Low Battery Recovery*, AICL* and USB On-The-Go Support | Summit Microelectronics | |
| FAN54010 | USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator | Fairchild Semiconductor | |
| SMB138 | Programmable Switch-mode, USB/AC Input Li+ Battery Charger with TurboCharge™ Mode and USB “On- the-Go” Power | Summit Microelectronics | |
| RT9503 | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology | |
| RT9503A | Fully Integrated Linear Single Cell Li-Ion Battery Charger with Power Path | Richtek Technology |
English 한국어 简体中文 日本語 español
ru.datasheetbank.com
